The Superior Biological Nutrient Removal Process
Better Biological Nutrient Removal Performance at a Lower Cost
Philadelphia Mixing Solutions and Mixing Solutions Limited delivers superior biological nutrient removal (BNR) for waste treatment facilities with the ARI 2 Anoxic Mixing System. The new system produces superior nutrient removal with lower capital outlays, reduced energy consumption and improved reliability and maintenance cost control through the life of the waste treatment facility.
Superior biological nutrient removal performance is delivered by improving the mixing performance of the equipment installed on continuous flow anaerobic, anoxic and aerobic mixing trains. The anaerobic and anoxic mixing processes must maintain optimal solid suspension in the tank while maximising surface contact with the anoxic bacteria that utilise the nutrients in the waste stream. This process must occur in an environment of low surface turbulence to reduce air entrainment that could reduce oxygen-free anoxic activity.
In the aerobic phase of the BNR process, fine bubbles of air need to be dispersed uniformly from the impeller to promote bacterial growth across the tank.
Superior Continuous Flow Mixing Performance
BNR systems are configured in trains of alternating anaerobic, anoxic and aerobic processes. The process steps combine to steadily degrade solids and nutrient content to meet wastewater discharge quality.
To deliver a superior mixing outcome each tank installation in the train must maximise the contact of the waste stream with the anoxic or aerobic bacteria that will remove the nutrients. we have developed an axial flow impeller, the anti-ragging ARI 2, specifically for anoxic BNR processes. The ARI 2 delivers mixing energy into the corners of the blending tanks to keep solids in suspension and encourage maximum biological activity.
The downward thrust of the axial flow produces mixing at the bottom of the tank and reduces surface turbulence and air incorporation that can reduce anoxic activity. The result is a more effective biological process that lowers output nutrient content as the waste stream moves through successive tanks.
Less Horsepower, Less Energy, Fewer Bridges, More Efficient
Our optimised solution uses less horsepower, less energy and fewer bridges.
The traditional configuration of BNR tanks utilises two mixers per mixing zone. Our optimised configuration for BNR reduces the number of mixers to one more efficient mixer, providing lower energy consumption and less infrastructure requirements.
Lower Capital and Operation Costs
The high-efficiency ARI 2 impeller is able to deliver its mixing performance using 20% less power than conventional turbine technology. This reduces capital spending with smaller mixer drive requirements, lower horsepower motors and less structural support for suspended equipment and wetted ends. Operating costs are reduced through lower energy use by the smaller equipment packages. The result is lower up-front expense at installation and continuing energy cost savings throughout the life of the facility.
Maintenance Cost Savings
The ARI 2 impeller is configured to resist the accumulation of fibrous solids on the impellers during operation— ragging. The accumulation of rags over time increases the loads on the gearbox and wetted ends creating a greater risk of motor overloads and component failure. Accumulation also requires regular planned shutdowns to clear the impellers of rags. This reduces plant performance capabilities while increasing on-going maintenance expense. The superior ARI 2 keeps the treatment facility on-mission to treat a continuous waste stream.
Fine Bubble Aerobic Processing
We use the anti-ragging GDX impeller in the aerobic phase of the BNR process. The GDX applies shear through mechanical mixing to produce fine bubbles from air injected near the impeller and then disperses the bubbles throughout the vessel to provide oxygen for the aerobic treatment process. This eliminates the use of a diffuser grid for oxygenation and saves capital expense on the project. The all stainless steel construction reduces maintenance costs over the life of the mixing unit.
The GDX can also be deployed as an impeller without the use of air injection. This provides process flexibility in swing zones that will change operations seasonally.
Low Speed Surface Aeration
In aerobic treatment, our low speed surface aerator, or TalonTM, used in conjunction with one of our purpose-built mixer drives, maximises oxygen transfer and eliminates performance reduction over time due to fouling.
Our low speed surface aeration solution provides the following advantages:
- Applicable/adaptable to most aeration operations
- Easily retro-fitted to existing aeration basins
- Capable of more transfer using less power vs. competitive options
- Uses a higher tangential component of velocity to achieve better mixing
- Maintains high transfer efficiency as output speed is decreased, ideal for variable frequency drives (VFD)
- Significantly improves oxygen transfer compared to traditional designs
Transfer 25% more oxygen without additional power input or maintain existing transfer performance while saving 25% on energy.